Whet pixel markWhet

Whet user guide, chapter 13, 2026-10-09

Known limits

Read this before you rely on a result. It lists what Whet does not do, what it refuses and how that looks in the window. Where a limit may have changed in your build and could not be confirmed, the line says "(to be checked)".

How Whet refuses

A greyed control always has a reason. Hover over it, or read the status bar. A refusal from an engine is shown in the engine's own words. Whet does not quietly do something else. If a study is refused, nothing was solved.

A missing number is shown as a dash, not as a low number standing in for "unknown". A factor of safety of "-" means the material has no yield strength on its card.

The trial

Without a licence there are six caps: 5000 mesh nodes in one study, 5 parts in an assembly, 10 s of simulated time, 5 bodies in a rig, a 30 s video cut and a 1920 by 1080 render. The assistant needs a licence, and reports and drawing sheets carry a trial mark. See Licence, trial and updates. A licence removes all six.

With a licence there is no size cap. What stops a big job is your machine and the engine. A study that will not end stops at a run timeout, 300 seconds by default.

Platforms

macOS runs on Apple silicon only. Linux is x86_64 with glibc 2.35 or newer. Windows is 10 or 11, x64; the installer is not code-signed yet, so SmartScreen warns before it runs. Blender is not included. See System requirements.

Parts

  • Units are millimetres and degrees.
  • Meshes are made of tetrahedra only. See Strength and Heat below.
  • A sweep carries one section along a path with mitred corners. Nothing varies along the path.
  • A non-uniform scale turns curves into smooth splines. The volume is held to a tenth of a percent and the step is refused if it misses.
  • A joint anchor is typed, not picked. The four face joints (distance, parallel, perpendicular, angle) take a side or a flat face from a list.
  • A mirror takes a plane, not a named face. A whole assembly cannot be mirrored (to be checked).
  • A joint's anchor and travel, friction and motor torque are things you declare. A CAD assembly does not carry them.
  • At most eight sketches can be open in one session. The undo history holds 1024 whole states.
  • A part can take thousands of features. The bound past that is memory. A plate cut by about 2000 holes took about a minute and 4 GB.
  • Scan to CAD has no cap command. Surfaces fitted one by one sew into a solid only when they share curves. See Scan to CAD.

Strength and Heat

  • The mesh is tetrahedra, first or second order. There are no shell or beam elements. A thin sheet-metal part is studied with solid elements through its wall, and the trial's 5000 nodes will usually refuse it.
  • There is no local refinement at a fillet from the window. Mesh finer where the peak sits and check the mesh convergence note.
  • A load is a Force, a Pressure or a Moment through a point. There is no bearing load through a hole.
  • A Pressure is refused beside buckling, a harmonic sweep and plasticity.
  • A transient heat study does not drive a stress step. A heat study takes no mechanical load.
  • There is no creep, no hyperelastic material and no transient structural dynamics.
  • The harmonic response rests on a damping ratio you type.
  • Fatigue and plasticity rest on data the material cards do not carry. An endurance limit, a stress-life pair and a hardening curve are typed and recorded as typed. A typed value is a claim, not a measurement.
  • Of the 200 material cards that ship, 107 state a yield strength. A study on one of the other 93 shows no factor of safety.
  • Gradient steps in the sensitivity page are one step, not topology optimisation.
  • The solver used on Windows is an older version than on macOS and Linux, so figures can differ a little.
  • A peak stress at a sharp corner is a mesh artifact. It grows as the mesh gets finer. Read the nodal average and look at convergence before you trust a corner.
  • Not every setting of a study can be set from the window. A restraint about an axis, a selection by cylinder or union, a contact pair and a spin are set in the study file, not in the panel (to be checked in your build). A material per body is set in the Thermal and Strength panels.

Motion

  • Collision uses the convex hull of each mesh. A pocket or a hole is solid to a contact.
  • A watched gap is read once per step. Two bodies that crossed and parted between two steps are missed.
  • A coupling has no tooth, backlash or efficiency modelled. Friction has no dependence on speed, temperature or wear.
  • There is no gait. A drive can follow a table of times and values, and nothing plans a step.
  • A reach envelope for a tool is a declared cylinder. It is not a model of a spanner or a hand.

Machining

  • Four operations run: Profile, Pocket Shape, Face and Drilling. The other operations are greyed.
  • One tool and one operation per job. No adaptive clearing, tapping, engraving or 3D operations, and no material-removal simulation.
  • Posts: linuxcnc and grbl.

Video and audio

Only a small set of operations is exposed: probe, cut, stills, strips, loudness, transcribe and speak. No stabilisation, overlay, crop or frame-rate conversion.

The assistant

  • Using it needs a licence.
  • It is slow on local models. An 8B model on a second machine answered in 52 to 180 seconds. On a computer with no graphics card the speed is not measured yet.
  • The checker finds claims it cannot match to your records. It does not prove geometry or physics. It can miss a false claim and flag a true one.
  • S and M local sizes are retired. L is the working size. Ultra needs 28.0 GB more memory than Whet, 48 GB in total, and has not been shown to be better than L.
  • No local model has been measured judging claims on a Mac. The memory floors come from Linux.
  • A picture sent to a text model is not seen.
  • Steps are a fixed set. Some requests are answered in words with no step.
  • A plan is approved by you. A model cannot approve or pick for you.
  • Prices are in US dollars and come from a dated list. Off-peak rates are not applied. A plan's remaining quota counts only Whet's own calls, so it is an upper bound.

Your own server

  • Studies, simulations and renders go over ssh with your own key. The engine versions on both machines must match. A mismatch is refused.
  • A model on a second machine runs through Ollama only, L or Ultra.
  • Whet does not measure the other machine's memory or disk.
  • The mesh tool is not offloaded.

See Your own server.

Import and export

Only formats the engine supports are listed in Import and export. A format marked planned there does not work yet.

Safety

Whet does not certify a design. A study is a model of a part under the loads and supports you state. Check results with your own judgement and, where it matters, a method that is accepted for your industry.